ECU Chip Tuning Siemens/Continental EMS24xx

Siemens/Continental EMS24xx calibration — Siemens/Continental control unit. Supported: Stage 1 — power tuning, software removal of EGR / catalyst control / EVAP, disabling the intake flaps, the Pops & Bangs effect, speed limit removal, DTC removal, return to stock and Cold Start Off on 8 modifications on Mustang and Ford. Reading via KESS3 / KTAG / Autotuner / MagicMotorSport.

8 engines in database 2 brands 11 options

Supported Options

CHECK STOCK OR NOT

CHECK STOCK OR NOT

CHECK STOCK OR NOT — проверка файла на наличие заводской (оригинальной) прошивки или внесённых изменений.

Learn more about the service
STAGE 1

STAGE 1

Stage 1 — это программный тюнинг двигателя без установки механических деталей. Он улучшает работу двигателя, повышает мощность и крутящий момент, сохраняя надежность и безопасность.

Learn more about the service
DTC OFF

DTC OFF

DTC Off — это программное отключение кодов ошибок, при котором выбранные ошибки больше не отображаются и не вызывают аварийный режим.

Learn more about the service
VMAX OFF

VMAX OFF

VMAX Off — это программное отключение ограничителя максимальной скорости, позволяющее автомобилю развивать скорость без заводских ограничений.

Learn more about the service
EVAP OFF

EVAP OFF

EVAP Off — это программное отключение системы улавливания паров топлива, которое устраняет ошибки и проблемы, связанные с работой этой системы.

Learn more about the service
COLD START OFF

COLD START OFF

Cold Start Off — это программное отключение холодного запуска, которое убирает повышенные обороты и громкую работу двигателя при запуске, делая запуск более мягким и комфортным.

Learn more about the service
FLAPS OFF

FLAPS OFF

Flaps Off — это программное отключение впускных заслонок, которое предотвращает их заклинивание, улучшает надежность двигателя и устраняет связанные с ними ошибки.

Learn more about the service
POP AND BANGS

POP AND BANGS

Pop and Bangs — это программная функция, создающая хлопки и треск в выхлопной системе при сбросе газа, делая звук автомобиля более спортивным.

Learn more about the service
CAT/LAMBDA OFF

CAT/LAMBDA OFF

CAT/Lambda Off — это программное отключение катализатора и лямбда-зондов, которое устраняет ошибки, предупреждения и ограничения, связанные с системой выхлопа.

Learn more about the service
EGR OFF

EGR OFF

EGR Off — это программное отключение системы EGR, которое уменьшает нагар во впуске, улучшает работу двигателя и устраняет связанные с системой ошибки.

Learn more about the service
RESET TO STOCK

RESET TO STOCK

Reset to Stock — это возврат программного обеспечения блока управления двигателем в оригинальное заводское состояние.

Learn more about the service

Brands with ECU Siemens/Continental EMS24xx

Frequently asked questions

Which vehicles use the Siemens/Continental EMS24xx ECU?

The Siemens/Continental EMS24xx is used across 2 brands: Mustang (5), Ford (3). 8 engines in total in the database.

Which modifications are available for the Siemens/Continental EMS24xx?

The Siemens/Continental EMS24xx ECU supports: CHECK STOCK OR NOT, STAGE 1, DTC OFF, VMAX OFF, EVAP OFF, COLD START OFF, FLAPS OFF, POP AND BANGS, CAT/LAMBDA OFF, EGR OFF. Checksums are recalculated on the engineer's side in WinOLS5.

What tool is used to flash the Siemens/Continental EMS24xx?

The Siemens/Continental EMS24xx is supported by: KESS3, Autotuner, MPPS, KTAG, CMD Flash, Trasdata, MagicMotorSport. On production models OBD reading is usually enough; on locked variants — Bench (BDM/JTAG).

What does Stage 1 give on the Siemens/Continental EMS24xx ECU?

Stage 1 on the petrol Siemens/Continental EMS24xx reprograms ignition timing, lambda target, boost target and wastegate duty (on turbo), throttle response, VANOS/VVT phase, torque limiter.

What Siemens/Continental EMS24xx file format is needed for flashing?

Siemens/Continental EMS24xx calibration requires a full read of the unit — bin/hex/ori. Programmers: KESS3 / Autotuner / CMD Flash / FGTech Galletto. Checksums — on the engineer's side.

Siemens/Continental EMS24xx file turnaround time at CHIPOK?

Reading and writing over OBD take 25-30 minutes. Bench reading requires opening the unit — about 60 minutes. Remote processing of a Siemens/Continental EMS24xx file at CHIPOK — 5-30 minutes.

How much does flashing the Siemens/Continental EMS24xx ECU cost?

The price of Siemens/Continental EMS24xx calibration depends on the selected options: Stage 1/2, DPF/EGR/AdBlue off, DTC off. The Max Price cap limits the package total. Paid with CHIPOK credits (1 cr = 1 €).