Valtra S Series 253 8.4L R6(217kW) 295hp — Stage 1 file (+40 hp)
hp
Stage 1 file for Valtra S Series 253 8.4L R6(217kW) 295hp
Target +0 hp. Custom development for your engine.
Chip tuning for Valtra S Series 253 8.4L R6(217kW) 295hp ECU
Valtra S Series (I) 253 8.4L R6(217kW) 295hp — agricultural diesel engine of the agricultural segment of the AGCO Corporation group (Финляндия, 1951). Stage 1 chip tuning raises power from 295 to 335 hp (+40 hp, +14%) and torque from 1300 to 1480 Nm (+180 Nm).
Valtra is a Finnish tractor manufacturer, founded in 1951. Valtra is part of AGCO Corporation. Valtra specialises in tractors built for Nordic conditions. DPF/SCR с AdBlue — стандарт на современных Tier 4/Stage V агро-моторах. Высокомощные агро-дизели — флагманские тракторы и комбайны. Сельхоз дизели имеют расширенный набор карт под нагрузку и работу на низких оборотах.
Сельхозсегмент — расход и тяга важнее л.с. Stage 1 в агросегменте фокусируется на крутящем моменте для тяговых работ. Высокомощные агро-Stage 1 — фокус на снижении расхода под нагрузкой. Высокомощные Valtra — флагманские тракторы и комбайны с уверенным запасом под Stage 1.
Frequently asked questions
How much does the power of the Valtra S Series 253 8.4L R6(217kW) 295hp increase after Stage 1?
Stage 1 chip tuning on the Valtra S Series 253 8.4L R6(217kW) 295hp boosts engine output by 40 hp: from 295 to 335 hp. Torque rises from 1300 to 1480 Nm (+180 Nm).
What changes in the Valtra S Series ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the Valtra S Series with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +40 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the Valtra S Series?
Stage 1 on the powerful Valtra S Series 253 8.4L R6(217kW) 295hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
What is Stage 2 for the Valtra S Series 253 8.4L R6(217kW) 295hp?
Stage 2 for the Valtra S Series 253 8.4L R6(217kW) 295hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does the factory warranty of the Valtra S Series remain valid after Stage 1?
After remapping the Valtra S Series, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Valtra S Series?
Reading and writing via OBD takes 25-30 minutes on the Valtra S Series. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Valtra S Series?
Before Stage 1 the original of the Valtra S Series 253 8.4L R6(217kW) 295hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Valtra S Series 253 8.4L R6(217kW) 295hp cost?
The remap price for the Valtra S Series 253 8.4L R6(217kW) 295hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.