Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm — Stage 1 file (+72 hp)
hp
Stage 1 file for Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm ECU
Valtra S Series (I) 292 8.4L R6 396hp (291kW) 1400Nm — agricultural diesel engine of the agricultural segment of the AGCO Corporation group (Финляндия, 1951). Stage 1 chip tuning raises power from 396 to 468 hp (+72 hp, +18%) and torque from 1400 to 1696 Nm (+296 Nm).
Valtra specialises in tractors built for Nordic conditions. Valtra is a Finnish tractor manufacturer, founded in 1951. Valtra is part of AGCO Corporation. Заводская калибровка сельхоз-дизелей консервативна — большой запас под Stage 1. Сельхозтехника — основной объект тюнинга в агросегменте; прирост момента критичен для тяговых работ. DPF/SCR с AdBlue — стандарт на современных Tier 4/Stage V агро-моторах.
Stage 1 в агросегменте фокусируется на крутящем моменте для тяговых работ. Сельхозсегмент — расход и тяга важнее л.с. Топ Valtra — мощностной потолок агросегмента.
Frequently asked questions
How many horsepower does the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm reach after a remap?
Stage 1 for the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm adds +72 hp — power increases from 396 to 468 hp (+18%). Torque rises from 1400 to 1696 Nm (+296 Nm).
What does a Stage 1 remap of the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm include?
Stage 1 on the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +72 hp with no hardware changes.
What does Stage 1 give on the top-spec Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm?
On the top-spec Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
How does Stage 2 differ from Stage 1 on the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm?
Stage 2 for the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does Stage 1 void the warranty on the Valtra S Series?
Stage 1 on the Valtra S Series voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm done?
The full remap cycle for the Valtra S Series — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Valtra S Series?
The original Valtra S Series ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm?
The cost of Stage 1 for the Valtra S Series 292 8.4L R6 396hp (291kW) 1400Nm is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.