ECU Chip Tuning Denso RA6

Denso ECU — Toyota/Mazda/Subaru, a closed platform with a proprietary algorithm — found only on Mitsubishi. On the Denso RA6, CHIPOK performs Stage 1 — power tuning and software removal of the diesel particulate filter, EGR, AdBlue. Flashing is done via KESS3 / Autotuner / CMD Flash / FGTech Galletto.

0 engines in database 1 brand 5 options

Supported Options

CHECK STOCK OR NOT

CHECK STOCK OR NOT

CHECK STOCK OR NOT — проверка файла на наличие заводской (оригинальной) прошивки или внесённых изменений.

Learn more about the service
DPF OFF

DPF OFF

DPF Off — это программное отключение сажевого фильтра, которое устраняет ошибки, аварийный режим и частые регенерации, улучшая стабильность работы двигателя.

Learn more about the service
STAGE 1

STAGE 1

Stage 1 — это программный тюнинг двигателя без установки механических деталей. Он улучшает работу двигателя, повышает мощность и крутящий момент, сохраняя надежность и безопасность.

Learn more about the service
ADBLUE OFF

ADBLUE OFF

AdBlue Off — это программное отключение устраняет ошибки по уровню и давлению жидкости, отключает работу насоса и форсунки впрыска, упрощает эксплуатацию и обеспечивает стабильную работу двигателя.

Learn more about the service
EGR OFF

EGR OFF

EGR Off — это программное отключение системы EGR, которое уменьшает нагар во впуске, улучшает работу двигателя и устраняет связанные с системой ошибки.

Learn more about the service

Brands with ECU Denso RA6

Mitsubishi 0

Frequently asked questions

Which cars use the Denso RA6 unit?

The Denso RA6 unit is found on 0 different engines. Main brands: Mitsubishi (0).

Which options does the Denso RA6 ECU support?

The Denso RA6 ECU supports: CHECK STOCK OR NOT, DPF OFF, STAGE 1, ADBLUE OFF, EGR OFF. Checksums are recalculated on the engineer's side in WinOLS5.

Which programmer is needed for the Denso RA6?

The Denso RA6 is supported by: specialized tooling (Toyota Denso is closed to standard WinOLS). On production models OBD reading is usually enough; on locked variants — Bench (BDM/JTAG).

What is the effect of Stage 1 on the Denso RA6 unit?

Stage 1 on the Denso RA6 reprograms the main ECU maps: injection, boost, torque. The exact set depends on the fuel type and architecture.

What should you send to CHIPOK for Denso RA6 calibration?

The original bin/hex/ori is accepted after reading via KESS3 / KTAG / Autotuner / MagicMotorSport. Checksums are recalculated on the engineer's side.

How long does flashing the Denso RA6 ECU take?

OBD flashing of the Denso RA6 — 25-30 minutes, Bench (if needed) — about an hour. The file processing itself takes 5-30 minutes after receipt.

What is the price of Denso RA6 calibration?

The cost of a Denso RA6 file is built in the calculator: you pick the operations you need (Stage 1, emissions removals, service operations) and the price is calculated with the package discount applied.