Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm — Stage 1 file (+40 hp)
hp
Stage 1 file for Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm ECU
Massey Ferguson 8000 Series (I) 8480 290hp (213kW) 1190Nm — agricultural diesel engine of the agricultural segment of the AGCO Corporation group (Великобритания, 1953). Stage 1 chip tuning raises power from 290 to 330 hp (+40 hp, +14%) and torque from 1190 to 1344 Nm (+154 Nm).
Massey Ferguson is a high-volume tractor brand in Europe. Massey Ferguson is a British-Canadian agricultural machinery manufacturer, founded in 1953. Massey Ferguson is part of AGCO Corporation. DPF/SCR с AdBlue — стандарт на современных Tier 4/Stage V агро-моторах. Высокомощные агро-дизели — флагманские тракторы и комбайны. Сельхоз дизели имеют расширенный набор карт под нагрузку и работу на низких оборотах.
Stage 1 в агросегменте фокусируется на крутящем моменте для тяговых работ. Высокомощные агро-Stage 1 — фокус на снижении расхода под нагрузкой. Сельхозсегмент — расход и тяга важнее л.с. Высокомощные Massey Ferguson — флагманские тракторы и комбайны с уверенным запасом под Stage 1.
Frequently asked questions
How much does the power of the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm increase after Stage 1?
Stage 1 for the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm adds +40 hp — power increases from 290 to 330 hp (+14%). Torque rises from 1190 to 1344 Nm (+154 Nm).
What does a Stage 1 remap of the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm include?
Stage 1 on the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +40 hp with no hardware changes.
What does Stage 1 give on the powerful Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm?
Stage 1 on the powerful Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
How does Stage 2 differ from Stage 1 on the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm?
Stage 2 for the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does Stage 1 void the warranty on the Massey Ferguson 8000 Series?
Stage 1 on the Massey Ferguson 8000 Series voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm done?
The full remap cycle for the Massey Ferguson 8000 Series — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Massey Ferguson 8000 Series?
The original Massey Ferguson 8000 Series ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm?
The cost of Stage 1 for the Massey Ferguson 8000 Series 8480 290hp (213kW) 1190Nm is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.