Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp — Stage 1 file (+5 hp)
hp
Stage 1 file for Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp ECU
Land-Rover Rover (2018) 5.0 V8 supercharged (SVR) 575 hp — premium petrol engine of the passenger segment of the Tata Motors (Jaguar Land Rover) group (Великобритания, 1922). Stage 1 chip tuning raises power from 575 to 580 hp (+5 hp, +1%) and torque from 680 to 685 Nm (+5 Nm). This engine ships with different ECU variants: Bosch MED17.8.31, Bosch MED17.8.32. The flashing method is determined by the specific unit: OBD, Bench or Boot mode. The ZF 8HPxx TCU is calibrated with a separate file — torque limiter and shift maps for Stage 1. In the CHIPOK database: 3 configurations · 3 ECU variants. A modern petrol engine built in 2018 — a generation with encrypted ECU protection (Tricore TPROT); top engines require Bench.
Land Rover is a British manufacturer of premium off-roaders and SUVs, founded in 1948. Land Rover is part of Tata Motors via Jaguar Land Rover (JLR). Land Rover specialises in premium off-roaders — the Range Rover, Discovery and Defender. Jaguar's petrol range spans turbocharged Ingenium units and supercharged V6/V8 engines. Jaguar shares some ECUs with Ford (a Visteon legacy). Modern Jaguar SVR models usually require a Bench read.
The supercharged Jaguar V8 comfortably reaches Stage 2 with the right hardware. The Jaguar community is a premium chip tuning niche in the UK and Europe. Modern Jaguars use Tricore protection and often require a Bench read. The top Jaguar SVR engines (supercharged V8) mark the ceiling of British premium performance.
Jaguar uses the ZF 8HP, a premium 8-speed automatic. SVR models use a reinforced ZF 8HP.
Frequently asked questions
How much horsepower does Stage 1 add for the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp?
The Stage 1 gain for the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp is 5 hp (+1%) over the stock 575 hp, for a total of 580 hp. Torque rises from 680 to 685 Nm (+5 Nm).
What is Stage 1 chip tuning for the Land-Rover Rover?
Stage 1 is a software optimization of the factory ECU firmware of the Land-Rover Rover with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +5 hp with no hardware changes.
Does Stage 1 make sense on the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp with this much power?
Stage 1 for the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp unlocks the potential built in by the factory but artificially capped to meet mass-market targets. A base of 750-800 hp is achievable once hardware is added.
What is Stage 2 for the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp?
Stage 2 on the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Which control units is the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp built with?
The Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp comes with 2 ECU variants: Bosch MED17.8.31, Bosch MED17.8.32. Calibration is done for the specific unit after the revision is identified.
What does remapping the ZF 8HPxx gearbox give on the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp?
The ZF 8HPxx TCU is calibrated separately: the torque limit is raised, the shift maps are optimized for the Stage 1 characteristics, and launch control is re-tuned. The TCU file is flashed separately from the ECU.
Does the factory warranty of the Land-Rover Rover remain valid after Stage 1?
After remapping the Land-Rover Rover, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Land-Rover Rover?
Reading and writing via OBD takes 25-30 minutes on the Land-Rover Rover. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Land-Rover Rover?
Before Stage 1 the original of the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp cost?
The remap price for the Land-Rover Rover 5.0 V8 supercharged (SVR) 575 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.