Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm — Stage 1 file (+72 hp)
hp
Stage 1 file for Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm ECU
Iveco Trakker (I) Cursor13 - 500 12.9 500hp (368kW) 2300Nm — commercial diesel engine of the commercial segment of the Iveco Group / CNH Industrial group (Италия, 1975). Stage 1 chip tuning raises power from 500 to 572 hp (+72 hp, +14%) and torque from 2300 to 2680 Nm (+380 Nm).
The Iveco Stralis and S-Way are long-haul tractor units. Cursor is the range of Iveco/CNH commercial diesel engines. Iveco shares some engines with Case and New Holland within CNH/FPT. Mid-generation truck models use standard OBD read/write. Top diesels in long-haul tractors sit at the power ceiling, and Stage 2 requires hardware. The factory calibration is conservative, leaving headroom for Stage 1 while preserving engine life.
The truck chip tuning community is an industry of its own, focused on long-haul routes. The professional logistics segment tunes for fuel consumption and pulling characteristics. Top MAN units sit at the power ceiling of the European truck segment.
Frequently asked questions
What power gain do you get after chip tuning the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm?
Stage 1 chip tuning on the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm boosts engine output by 72 hp: from 500 to 572 hp. Torque rises from 2300 to 2680 Nm (+380 Nm).
What changes in the Iveco Trakker ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the Iveco Trakker with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +72 hp with no hardware changes.
Does Stage 1 make sense on the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm with this much power?
On the top-spec Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
What is Stage 2 for the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm?
Stage 2 for the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does the factory warranty of the Iveco Trakker remain valid after Stage 1?
After remapping the Iveco Trakker, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Iveco Trakker?
Reading and writing via OBD takes 25-30 minutes on the Iveco Trakker. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Iveco Trakker?
Before Stage 1 the original of the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm cost?
The remap price for the Iveco Trakker Cursor13 - 500 12.9 500hp (368kW) 2300Nm is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.