Bosch ME17.9.7 Immo Off: Lada
Immo Off on the Bosch ME17.9.7 control unit for vehicles Lada. Upload the dump — free analysis and check; apply the operation and download the ready file in your portal account.
Disabling the immobilizer in the ECU firmware — the engine starts without binding to a key and BCM.
| Operation | Immo Off |
|---|---|
| Control unit | Bosch ME17.9.7 |
| Car makes | Lada |
| Access / memory | INT FLASH [TC1762] |
| INT FLASH | TC1762 |
| Method | Online, from the ECU memory dump (.bin) |
| Applicability check | Free |
| Checksums | Recalculated automatically |
| Result | A ready file to write to the unit |
Bosch ME17.9.7 Immo Off — 3 cars
Operation Immo Off is supported for the Bosch ME17.9.7 block on vehicles Lada. In the list: Lada Niva. Upload the dump — the system detects the version and checks applicability for free.
| Make | Model | Version | Year |
|---|---|---|---|
| Lada | Niva | 1.7 | 2020 |
| Lada | Niva | 1.7 | 2011 |
| Lada | Niva | 1.7 MPI | 2015 |
Bosch ME17.9.7 Immo Off — for Lada
Immo Off is disabling the immobilizer right in the engine control unit's firmware. After the operation the ECU stops checking the key tag against the BCM, CAS or EWS and starts the engine without binding to the car.
When you need Immo Off
- Installing a used (donor) unit — an ECU from another car is not matched to your key and BCM.
- Lost or broken keys — you need to start the engine while keys are being restored.
- Board repair or processor replacement — after servicing, the immobilizer binding is lost.
- Moving the ECU to a bench — starting the engine outside the car, without the factory security system.
What you get: the unit starts the engine without the immobilizer — the key tag and BCM are no longer checked.
Bosch ME17.9.7 memory and reading
The Bosch ME17.9.7 unit uses the following: INT FLASH — TC1762. The Immo Off operation works on the INT FLASH [TC1762] area — that is the one to read out and upload. If OBD reading is not available for this unit, the dump is taken on the bench via Bench or Boot mode.
For the Bosch ME17.9.7 block the «Immo Off» operation runs online from the ECU memory dump (access — INT FLASH [TC1762]). Read the file via OBD, Bench or Boot and upload it — the system detects Bosch ME17.9.7 and checks whether the operation applies for free. You'll get the ready file with recalculated checksums in your portal account.
Frequently asked questions
Immo Off on Bosch ME17.9.7 — short and to the point
What does Immo Off do on Bosch ME17.9.7?
Disabling the immobilizer in the ECU firmware — the engine starts without binding to a key and BCM.
Which file should I upload?
The ECU memory dump (access INT FLASH [TC1762]), read via OBD, Bench or Boot. Upload the file — the system detects Bosch ME17.9.7 for free and checks whether the operation applies.
How much does Immo Off cost?
Uploading and analyzing the file is free. Applying the operation and downloading the ready file happen in your portal account (40 €).
Are the checksums recalculated?
Yes, automatically. The ready file is immediately writable to the unit — no need to recalculate checksums by hand.
Which vehicles is it for?
Bosch ME17.9.7 with the Immo Off operation covers Lada. The system detects the exact version from the uploaded dump.
What memory and processor does Bosch ME17.9.7 use?
Memory of the unit: INT FLASH — TC1762. The Immo Off operation needs INT FLASH [TC1762] access.