Bosch ME17.1.6 Immo Data: Bentley
Immo Data on the Bosch ME17.1.6 on the TC1797 processor control unit for vehicles Bentley. Upload the dump — free analysis and check; apply the operation and download the ready file in your portal account.
Reading VIN, PIN, keys and other immo parameters from an ECU dump — diagnostics and cross-checking without modifying the file.
| Operation | Immo Data |
|---|---|
| Control unit | Bosch ME17.1.6 |
| Car makes | Bentley |
| Processor (MCU) | TC1797 |
| Access / memory | INT FLASH [TC1797] · INT EEPROM [TC1797] |
| INT FLASH | TC1797 |
| INT EEPROM | TC1797 |
| Method | Online, from the ECU memory dump (.bin) |
| Applicability check | Free |
| Checksums | Recalculated automatically |
| Result | A ready file to write to the unit |
Bosch ME17.1.6 Immo Data — 3 cars
Operation Immo Data is supported for the Bosch ME17.1.6 block on vehicles Bentley. In the list: Bentley Continental Gt, Bentley Flying Spur. Upload the dump — the system detects the version and checks applicability for free.
| Make | Model | Version | Year |
|---|---|---|---|
| Bentley | Continental Gt | 6.0 W12 Speed TwinTurbo 8AT | 2012 |
| Bentley | Flying Spur | 6.0 W12 TwinTurbo 8AT | 2013 |
| Bentley | Continental Gt | 6.0 W12 TwinTurbo 6AT | 2011 |
Bosch ME17.1.6 Immo Data — for Bentley
Immo Data reads the immobiliser parameters straight from an ECU dump: VIN, PIN/SKC, ISN, immobiliser status and the identifiers of the linked modules. The file is not modified, so the operation is safe and suits diagnostics.
When you need Immo Data
- Buying a used unit — check which car the ECU is tied to before fitting it.
- Key programming — get the PIN/SKC or ISN that your programming tool needs.
- No-start diagnostics — find out whether it is really the immobiliser blocking the engine.
- Cross-checking the modules — make sure the VIN and identifiers match between the ECU and the cluster.
What you get: the immobiliser parameters of the unit are read and displayed — the dump stays untouched.
Bosch ME17.1.6 memory and reading
The Bosch ME17.1.6 unit uses on the TC1797 processor the following: INT FLASH — TC1797, INT EEPROM — TC1797. The Immo Data operation works on the INT FLASH [TC1797] · INT EEPROM [TC1797] area — that is the one to read out and upload. If OBD reading is not available for this unit, the dump is taken on the bench via Bench or Boot mode.
For the Bosch ME17.1.6 block on the TC1797 processor the «Immo Data» operation runs online from the ECU memory dump (access — INT FLASH [TC1797] · INT EEPROM [TC1797]). Read the file via OBD, Bench or Boot and upload it — the system detects Bosch ME17.1.6 and checks whether the operation applies for free. You'll get the ready file with recalculated checksums in your portal account.
Frequently asked questions
Immo Data on Bosch ME17.1.6 — short and to the point
What does Immo Data do on Bosch ME17.1.6?
Reading VIN, PIN, keys and other immo parameters from an ECU dump — diagnostics and cross-checking without modifying the file.
Which file should I upload?
The ECU memory dump (access INT FLASH [TC1797] · INT EEPROM [TC1797]), read via OBD, Bench or Boot. Upload the file — the system detects Bosch ME17.1.6 for free and checks whether the operation applies.
How much does Immo Data cost?
Uploading and analyzing the file is free. Applying the operation and downloading the ready file happen in your portal account (50 €).
Are the checksums recalculated?
Yes, automatically. The ready file is immediately writable to the unit — no need to recalculate checksums by hand.
Which vehicles is it for?
Bosch ME17.1.6 with the Immo Data operation covers Bentley. The system detects the exact version from the uploaded dump.
What memory and processor does Bosch ME17.1.6 use?
The unit is built around the TC1797 processor. Memory of the unit: INT FLASH — TC1797, INT EEPROM — TC1797. The Immo Data operation needs INT FLASH [TC1797] · INT EEPROM [TC1797] access.