Bosch EDC17CP68 Immo Off: Volvo
Immo Off on the Bosch EDC17CP68 on the TC1797 processor control unit for vehicles Volvo. Upload the dump — free analysis and check; apply the operation and download the ready file in your portal account.
Disabling the immobilizer in the ECU firmware — the engine starts without binding to a key and BCM.
| Operation | Immo Off |
|---|---|
| Control unit | Bosch EDC17CP68 |
| Car makes | Volvo |
| Processor (MCU) | TC1797 |
| Access / memory | INT FLASH [TC1797] |
| INT FLASH | TC1797 |
| INT EEPROM | TC1797 |
| Method | Online, from the ECU memory dump (.bin) |
| Applicability check | Free |
| Checksums | Recalculated automatically |
| Result | A ready file to write to the unit |
Bosch EDC17CP68 Immo Off — 6 vehicles
Operation Immo Off is supported for the Bosch EDC17CP68 block on vehicles Volvo. In the list: Volvo V60, Volvo S60, Volvo V60 Cross Country, Volvo XC60, Volvo XC70. Upload the dump — the system detects the version and checks applicability for free.
| Make | Model | Version | Year |
|---|---|---|---|
| Volvo | V60 | 2.4 D6 AWD Plug-in Hybrid Geartronic 6AT | 2015 |
| Volvo | S60 | 2.4 20v D4 | 2015 |
| Volvo | V60 Cross Country | 2.4 20v D4 | 2015 |
| Volvo | XC60 | 2.4 20v D5 | 2015 |
| Volvo | XC70 | 2.4 20v D5 | 2015 |
| Volvo | V60 | 2.4 20v D4 | 2015 |
Bosch EDC17CP68 Immo Off — for Volvo
Immo Off is disabling the immobilizer right in the engine control unit's firmware. After the operation the ECU stops checking the key tag against the BCM, CAS or EWS and starts the engine without binding to the car.
When you need Immo Off
- Installing a used (donor) unit — an ECU from another car is not matched to your key and BCM.
- Lost or broken keys — you need to start the engine while keys are being restored.
- Board repair or processor replacement — after servicing, the immobilizer binding is lost.
- Moving the ECU to a bench — starting the engine outside the car, without the factory security system.
What you get: the unit starts the engine without the immobilizer — the key tag and BCM are no longer checked.
Bosch EDC17CP68 memory and reading
The Bosch EDC17CP68 unit uses on the TC1797 processor the following: INT FLASH — TC1797, INT EEPROM — TC1797. The Immo Off operation works on the INT FLASH [TC1797] area — that is the one to read out and upload. If OBD reading is not available for this unit, the dump is taken on the bench via Bench or Boot mode.
For the Bosch EDC17CP68 block on the TC1797 processor the «Immo Off» operation runs online from the ECU memory dump (access — INT FLASH [TC1797]). Read the file via OBD, Bench or Boot and upload it — the system detects Bosch EDC17CP68 and checks whether the operation applies for free. You'll get the ready file with recalculated checksums in your portal account.
Frequently asked questions
Immo Off on Bosch EDC17CP68 — short and to the point
What does Immo Off do on Bosch EDC17CP68?
Disabling the immobilizer in the ECU firmware — the engine starts without binding to a key and BCM.
Which file should I upload?
The ECU memory dump (access INT FLASH [TC1797]), read via OBD, Bench or Boot. Upload the file — the system detects Bosch EDC17CP68 for free and checks whether the operation applies.
How much does Immo Off cost?
Uploading and analyzing the file is free. Applying the operation and downloading the ready file happen in your portal account (60 €).
Are the checksums recalculated?
Yes, automatically. The ready file is immediately writable to the unit — no need to recalculate checksums by hand.
Which vehicles is it for?
Bosch EDC17CP68 with the Immo Off operation covers Volvo. The system detects the exact version from the uploaded dump.
What memory and processor does Bosch EDC17CP68 use?
The unit is built around the TC1797 processor. Memory of the unit: INT FLASH — TC1797, INT EEPROM — TC1797. The Immo Off operation needs INT FLASH [TC1797] access.