Volvo Penta D6 400 Marine 400hp (294kW) 980Nm — Stage 1 file (+70 hp)
hp
Stage 1 file for Volvo Penta D6 400 Marine 400hp (294kW) 980Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Volvo Penta D6 400 Marine 400hp (294kW) 980Nm ECU
Volvo Penta D6 400 (I) Marine 400hp (294kW) 980Nm — marine diesel engine of the marine segment of the Volvo Group group (Швеция, 1907). Stage 1 chip tuning raises power from 400 to 470 hp (+70 hp, +18%) and torque from 980 to 1112 Nm (+132 Nm).
Volvo Penta IPS is a signature propulsion system with steerable pods. Volvo Penta is the marine and industrial division of the Volvo Group, founded in 1907. Volvo Penta specialises in marine inboard engines and industrial diesels. The Volvo Penta D-series is a range of marine diesel engines.
Marine engines are a specialised chip tuning segment focused on torque and fuel consumption. Marine chip tuning is a narrow niche, with calibration tailored to propeller load and operating conditions. The top Mercury Marine units sit at the power ceiling of the marine segment.
Frequently asked questions
How much does the power of the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm increase after Stage 1?
The Stage 1 gain for the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm is 70 hp (+18%) over the stock 400 hp, for a total of 470 hp. Torque rises from 980 to 1112 Nm (+132 Nm).
What is Stage 1 chip tuning for the Volvo Penta D6 400?
Stage 1 on the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +70 hp with no hardware changes.
What does Stage 1 give on the top-spec Volvo Penta D6 400 Marine 400hp (294kW) 980Nm?
Stage 1 for the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm unlocks the potential built in by the factory but artificially capped to meet mass-market targets. A base of 750-800 hp is achievable once hardware is added.
How does Stage 2 differ from Stage 1 on the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm?
Stage 2 on the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Does Stage 1 void the warranty on the Volvo Penta D6 400?
Stage 1 on the Volvo Penta D6 400 voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm done?
The full remap cycle for the Volvo Penta D6 400 — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Volvo Penta D6 400?
The original Volvo Penta D6 400 ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm?
The cost of Stage 1 for the Volvo Penta D6 400 Marine 400hp (294kW) 980Nm is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.