Subaru Tribeca 3.0i (2006) 245 hp — Stage 1 file (+10 hp)
hp
Stage 1 file for Subaru Tribeca 3.0i (2006) 245 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Subaru Tribeca 3.0i (2006) 245 hp ECU
Subaru Tribeca (2006) 3.0i (2006) 245 hp — mass-market petrol engine of the passenger segment of the Subaru Corporation (Toyota владеет 20%) group (Япония, 1953). Stage 1 chip tuning raises power from 245 to 255 hp (+10 hp, +4%) and torque from 297 to 310 Nm (+13 Nm). A petrol engine built in 2006 — the era before widespread firmware encryption, OBD flash without complications.
STI (Subaru Tecnica International) is the performance division that builds the WRX STI. Subaru uses permanent all-wheel drive (AWD) on most of its models. The WRX STI is Subaru's iconic rally model. On the turbo WRX, Stage 1 delivers a confident gain. The WRX and WRX STI are the flagship of the brand's turbo segment. The EJ series (legacy) and the FA/FB series are Subaru's iconic Boxer engines.
On turbo Subaru engines, Stage 1 delivers a noticeable gain. The Subaru community in JDM and rally culture is the largest for the WRX/STI. High-output Subaru WRX models sit in the turbo segment, with solid headroom for Stage 1.
Frequently asked questions
How many horsepower does the Subaru Tribeca 3.0i (2006) 245 hp reach after a remap?
Stage 1 for the Subaru Tribeca 3.0i (2006) 245 hp adds +10 hp — power increases from 245 to 255 hp (+4%). Torque rises from 297 to 310 Nm (+13 Nm).
What does a Stage 1 remap of the Subaru Tribeca 3.0i (2006) 245 hp include?
Stage 1 is a software optimization of the factory ECU firmware of the Subaru Tribeca with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +10 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the Subaru Tribeca?
Stage 1 on the powerful Subaru Tribeca 3.0i (2006) 245 hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
What is Stage 2 for the Subaru Tribeca 3.0i (2006) 245 hp?
Stage 2 for the Subaru Tribeca 3.0i (2006) 245 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does the factory warranty of the Subaru Tribeca remain valid after Stage 1?
After remapping the Subaru Tribeca, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Subaru Tribeca?
Reading and writing via OBD takes 25-30 minutes on the Subaru Tribeca. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Subaru Tribeca?
Before Stage 1 the original of the Subaru Tribeca 3.0i (2006) 245 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Subaru Tribeca 3.0i (2006) 245 hp cost?
The remap price for the Subaru Tribeca 3.0i (2006) 245 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.