Smart ForTwo 0.7T 62 hp — Stage 1 file (+20 hp)
hp
Stage 1 file for Smart ForTwo 0.7T 62 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Smart ForTwo 0.7T 62 hp ECU
Smart ForTwo (2000) 0.7T 62 hp — mass-market petrol engine of the passenger segment of the Mercedes-Benz Group AG / Geely (с 2020 — JV) group (Германия, 1926). Stage 1 chip tuning raises power from 62 to 82 hp (+20 hp, +32%) and torque from 95 to 120 Nm (+25 Nm). A petrol engine built in 2000 — the era before widespread firmware encryption, OBD flash without complications.
The Smart #1 and #3 are the new generation of electric crossovers built on the Geely platform. Smart is a German compact-car brand within the Mercedes-Benz Group, and since 2020 a joint venture with Geely. Smart historically used Mitsubishi and Renault engines. The AMG 'one engineer, one engine' principle means each engine is built by a single craftsman whose signature appears on the plaque. The Mercedes petrol range spans compacts, premium saloons, SUVs, roadsters and AMG flagships. The factory calibration on Mercedes petrol engines is conservative, leaving headroom for Stage 1.
The AMG community is active in Germany, but the protection is the toughest in the industry, so Stage 1 on AMG usually requires Bench. Mercedes is one of the most protected brands in the chip tuning industry in terms of encryption. Stage 1 on Mercedes often requires refreshing the adaptations after the flash. In the Mercedes city segment, Stage 1 is more about comfort and responsiveness than power. On low-output Mercedes engines, Stage 1 is safe and does not over-stress the hardware. On naturally aspirated Mercedes engines without a turbo, the main effect is on throttle response.
Frequently asked questions
How many horsepower does the Smart ForTwo 0.7T 62 hp reach after a remap?
Stage 1 chip tuning on the Smart ForTwo 0.7T 62 hp boosts engine output by 20 hp: from 62 to 82 hp. Torque rises from 95 to 120 Nm (+25 Nm).
What changes in the Smart ForTwo ECU after Stage 1?
Stage 1 on the Smart ForTwo 0.7T 62 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +20 hp with no hardware changes.
Is Stage 1 safe for the low-output Smart ForTwo 0.7T 62 hp?
Yes, Stage 1 on the low-output Smart ForTwo 0.7T 62 hp delivers a moderate but genuine gain — without overstressing the hardware. On base naturally aspirated engines the effect is felt mainly as improved throttle response and a stronger mid-range.
How does Stage 2 differ from Stage 1 on the Smart ForTwo 0.7T 62 hp?
Stage 2 for the Smart ForTwo 0.7T 62 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does Stage 1 void the warranty on the Smart ForTwo?
Stage 1 on the Smart ForTwo voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Smart ForTwo 0.7T 62 hp done?
The full remap cycle for the Smart ForTwo — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Smart ForTwo?
The original Smart ForTwo ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Smart ForTwo 0.7T 62 hp?
The cost of Stage 1 for the Smart ForTwo 0.7T 62 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.