Skoda Rapid 1.0 TSI/TFSI 95 hp — Stage 1 file (+25 hp)
hp
Stage 1 file for Skoda Rapid 1.0 TSI/TFSI 95 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Skoda Rapid 1.0 TSI/TFSI 95 hp ECU
Skoda Rapid (2012) 1.0 TSI/TFSI 95 hp — mass-market petrol engine of the passenger segment of the Volkswagen Group (VAG) group (Чехия, 1895). Stage 1 chip tuning raises power from 95 to 120 hp (+25 hp, +26%) and torque from 175 to 235 Nm (+60 Nm). This engine ships with different ECU variants: Bosch MED17.1.27, Bosch MED17.5.21. The flashing method is determined by the specific unit: OBD, Bench or Boot mode. In the CHIPOK database: 2 configurations · 2 ECU variants. A petrol engine built in 2012 — a Tricore platform without strong protection; OBD access works.
Skoda has been part of the Volkswagen Group (VAG) since 1991. Skoda is a Czech carmaker from Mlada Boleslav, founded in 1895 and one of the oldest car factories in the world. The Skoda community in Eastern Europe is one of the most active in chip tuning. Mid-generation petrol models use standard OBD flash via MQB.
Within the VAG group, ECUs are standardised, so Skoda files often work on VW/Audi/Seat. The Skoda community benefits from a large pool of Stage files drawn from the shared VAG catalogue. On pre-2017 Skoda models, Stage 1 is done via OBD without bench. On low-output Skoda engines, Stage 1 is safe without overstressing the hardware. On naturally aspirated Skoda engines, the main effect is on throttle response. In the Skoda city segment, Stage 1 is more about comfort than outright power.
Frequently asked questions
How much does the power of the Skoda Rapid 1.0 TSI/TFSI 95 hp increase after Stage 1?
Stage 1 chip tuning on the Skoda Rapid 1.0 TSI/TFSI 95 hp boosts engine output by 25 hp: from 95 to 120 hp. Torque rises from 175 to 235 Nm (+60 Nm).
What changes in the Skoda Rapid ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the Skoda Rapid with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +25 hp with no hardware changes.
Is Stage 1 worth doing on the base Skoda Rapid?
Yes, Stage 1 on the low-output Skoda Rapid 1.0 TSI/TFSI 95 hp delivers a moderate but genuine gain — without overstressing the hardware. On base naturally aspirated engines the effect is felt mainly as improved throttle response and a stronger mid-range.
What is Stage 2 for the Skoda Rapid 1.0 TSI/TFSI 95 hp?
Stage 2 for the Skoda Rapid 1.0 TSI/TFSI 95 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Which control units is the Skoda Rapid 1.0 TSI/TFSI 95 hp built with?
The Skoda Rapid 1.0 TSI/TFSI 95 hp comes with 2 ECU variants: Bosch MED17.1.27, Bosch MED17.5.21. Calibration is done for the specific unit after the revision is identified.
Does the factory warranty of the Skoda Rapid remain valid after Stage 1?
After remapping the Skoda Rapid, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Skoda Rapid?
Reading and writing via OBD takes 25-30 minutes on the Skoda Rapid. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Skoda Rapid?
Before Stage 1 the original of the Skoda Rapid 1.0 TSI/TFSI 95 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Skoda Rapid 1.0 TSI/TFSI 95 hp cost?
The remap price for the Skoda Rapid 1.0 TSI/TFSI 95 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.