Skoda Kamiq 1.5 TSI 150 hp — Stage 1 file (+25 hp)
hp
Stage 1 file for Skoda Kamiq 1.5 TSI 150 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Skoda Kamiq 1.5 TSI 150 hp ECU
Skoda Kamiq (2019) 1.5 TSI 150 hp — mass-market petrol engine of the passenger segment of the Volkswagen Group (VAG) group (Чехия, 1895). Stage 1 chip tuning raises power from 150 to 175 hp (+25 hp, +17%) and torque from 250 to 300 Nm (+50 Nm). ECU — Bosch MG1CS011. Flashing method: OBD or Bench depending on the unit's protection. TCU units on this engine: Temic DQ200 (MQB), Temic DQ200G2, Bosch DQ38x — each is calibrated with a separate file (torque limiter, shift maps for Stage 1). In the CHIPOK database: 4 configurations · 4 ECU variants. A 2019 petrol engine — the latest era of encrypted firmware; OBD access is available on production units, Bench on sport models.
Skoda has been part of the Volkswagen Group (VAG) since 1991. Skoda is a Czech carmaker from Mlada Boleslav, founded in 1895 and one of the oldest car factories in the world. The Skoda community in Eastern Europe is one of the most active in chip tuning. The factory calibration of Skoda petrol engines is conservative, leaving headroom for Stage 1. Skoda shares ECUs and calibration algorithms with VW. Mid-range Skoda turbo petrol engines are a high-volume Stage 1 subject.
The Skoda community benefits from a large pool of Stage files drawn from the shared VAG catalogue. On Skoda, Stage 1 usually fits within the standard turnaround time. On mid-range standard Skoda petrol engines, Stage 1 delivers a noticeable gain. The Skoda community in Eastern Europe offers a large pool of ready-made Stage files. Mid-range Skoda engines form the backbone of the range; Stage 1 preserves engine life. The MQB platform is the most refined chip tuning segment in Europe.
DSG comes in dry- and wet-clutch versions. The DSG is VAG's signature dual-clutch gearbox, fitted to Skoda models with transverse engines. Tiptronic is the classic automatic for Skoda's top models.
Frequently asked questions
How much horsepower does Stage 1 add for the Skoda Kamiq 1.5 TSI 150 hp?
Stage 1 chip tuning on the Skoda Kamiq 1.5 TSI 150 hp boosts engine output by 25 hp: from 150 to 175 hp. Torque rises from 250 to 300 Nm (+50 Nm).
What changes in the Skoda Kamiq ECU after Stage 1?
Stage 1 on the Skoda Kamiq 1.5 TSI 150 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +25 hp with no hardware changes.
Is a Stage 1 remap safe for the 1.5 TSI 150 hp?
Stage 1 on the Skoda Kamiq 1.5 TSI 150 hp is developed while keeping the factory AFR, knock control and temperature limits. Engine life is preserved provided regular maintenance is carried out.
How does Stage 2 differ from Stage 1 on the Skoda Kamiq 1.5 TSI 150 hp?
Stage 2 for the Skoda Kamiq 1.5 TSI 150 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What control unit does the Skoda Kamiq 1.5 TSI 150 hp run?
The control unit of the Skoda Kamiq 1.5 TSI 150 hp is the Bosch MG1CS011. Before flashing, the engineer identifies the exact revision and selects the write method.
Which TCUs are found on the Skoda Kamiq 1.5 TSI 150 hp?
The Skoda Kamiq 1.5 TSI 150 hp was fitted with different automatic-transmission units: Temic DQ200 (MQB), Temic DQ200G2, Bosch DQ38x. All are supported via Bench reading; the Stage 1 calibration is done for the specific TCU after the revision is identified.
Does Stage 1 void the warranty on the Skoda Kamiq?
Stage 1 on the Skoda Kamiq voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Skoda Kamiq 1.5 TSI 150 hp done?
The full remap cycle for the Skoda Kamiq — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Skoda Kamiq?
The original Skoda Kamiq ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Skoda Kamiq 1.5 TSI 150 hp?
The cost of Stage 1 for the Skoda Kamiq 1.5 TSI 150 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.