Scania R-series 730 EU6 730hp (537kW) 3500Nm — Stage 1 file (+80 hp)
hp
Stage 1 file for Scania R-series 730 EU6 730hp (537kW) 3500Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Scania R-series 730 EU6 730hp (537kW) 3500Nm ECU
Scania R-series (I) 730 EU6 730hp (537kW) 3500Nm — commercial diesel engine of the commercial segment of the TRATON Group (Volkswagen Truck & Bus) group (Швеция, 1891). Stage 1 chip tuning raises power from 730 to 810 hp (+80 hp, +11%) and torque from 3500 to 3950 Nm (+450 Nm).
Scania is a Swedish manufacturer of trucks and buses, founded in 1891. Scania specialises in premium trucks and long-haul tractor units. Scania holds the largest share of the premium European truck segment. DPF/SCR with AdBlue is standard on modern Euro-6 truck engines. Truck chip tuning is a discipline of its own, focused on fuel consumption and pulling power rather than peak output. The factory calibration is conservative, leaving headroom for Stage 1 while preserving engine life.
The truck chip tuning community is an industry of its own, focused on long-haul routes. The professional logistics segment tunes for fuel consumption and pulling characteristics. Top MAN units sit at the power ceiling of the European truck segment.
Frequently asked questions
How much horsepower does Stage 1 add for the Scania R-series 730 EU6 730hp (537kW) 3500Nm?
Stage 1 for the Scania R-series 730 EU6 730hp (537kW) 3500Nm adds +80 hp — power increases from 730 to 810 hp (+11%). Torque rises from 3500 to 3950 Nm (+450 Nm).
What does a Stage 1 remap of the Scania R-series 730 EU6 730hp (537kW) 3500Nm include?
Stage 1 is a software optimization of the factory ECU firmware of the Scania R-series with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +80 hp with no hardware changes.
Does Stage 1 make sense on the Scania R-series 730 EU6 730hp (537kW) 3500Nm with this much power?
On the top-spec Scania R-series 730 EU6 730hp (537kW) 3500Nm engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
What is Stage 2 for the Scania R-series 730 EU6 730hp (537kW) 3500Nm?
Stage 2 for the Scania R-series 730 EU6 730hp (537kW) 3500Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does the factory warranty of the Scania R-series remain valid after Stage 1?
After remapping the Scania R-series, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Scania R-series?
Reading and writing via OBD takes 25-30 minutes on the Scania R-series. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Scania R-series?
Before Stage 1 the original of the Scania R-series 730 EU6 730hp (537kW) 3500Nm is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Scania R-series 730 EU6 730hp (537kW) 3500Nm cost?
The remap price for the Scania R-series 730 EU6 730hp (537kW) 3500Nm is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.