Scania R-series 560 560hp (412kW) 2700Nm — Stage 1 file (+85 hp)
hp
Stage 1 file for Scania R-series 560 560hp (412kW) 2700Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Scania R-series 560 560hp (412kW) 2700Nm ECU
Scania R-series (I) 560 560hp (412kW) 2700Nm — commercial diesel engine of the commercial segment of the TRATON Group (Volkswagen Truck & Bus) group (Швеция, 1891). Stage 1 chip tuning raises power from 560 to 645 hp (+85 hp, +15%) and torque from 2700 to 3105 Nm (+405 Nm).
Scania specialises in premium trucks and long-haul tractor units. Scania holds the largest share of the premium European truck segment. Scania is part of the TRATON Group (Volkswagen Truck & Bus). Top diesels in long-haul tractors sit at the power ceiling, and Stage 2 requires hardware. Mid-generation truck models use standard OBD read/write. Truck diesels carry an extended set of maps for commercial load, with the focus on torque.
The professional logistics segment tunes for fuel consumption and pulling characteristics. The truck chip tuning community is an industry of its own, focused on long-haul routes. Top MAN units sit at the power ceiling of the European truck segment.
Frequently asked questions
How much does the power of the Scania R-series 560 560hp (412kW) 2700Nm increase after Stage 1?
The Stage 1 gain for the Scania R-series 560 560hp (412kW) 2700Nm is 85 hp (+15%) over the stock 560 hp, for a total of 645 hp. Torque rises from 2700 to 3105 Nm (+405 Nm).
What is Stage 1 chip tuning for the Scania R-series?
Stage 1 is a software optimization of the factory ECU firmware of the Scania R-series with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +85 hp with no hardware changes.
Does Stage 1 make sense on the Scania R-series 560 560hp (412kW) 2700Nm with this much power?
Stage 1 for the Scania R-series 560 560hp (412kW) 2700Nm unlocks the potential built in by the factory but artificially capped to meet mass-market targets. A base of 750-800 hp is achievable once hardware is added.
What is Stage 2 for the Scania R-series 560 560hp (412kW) 2700Nm?
Stage 2 on the Scania R-series 560 560hp (412kW) 2700Nm means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Does the factory warranty of the Scania R-series remain valid after Stage 1?
After remapping the Scania R-series, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Scania R-series?
Reading and writing via OBD takes 25-30 minutes on the Scania R-series. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Scania R-series?
Before Stage 1 the original of the Scania R-series 560 560hp (412kW) 2700Nm is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Scania R-series 560 560hp (412kW) 2700Nm cost?
The remap price for the Scania R-series 560 560hp (412kW) 2700Nm is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.