Peugeot Partner 1.6 HDI (2008) 75 hp — Stage 1 file (+25 hp)
hp
Stage 1 file for Peugeot Partner 1.6 HDI (2008) 75 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Peugeot Partner 1.6 HDI (2008) 75 hp ECU
Peugeot Partner (2008) 1.6 HDI (2008) 75 hp — mass-market diesel engine of the passenger segment of the Stellantis group (Франция, 1810). Stage 1 chip tuning raises power from 75 to 100 hp (+25 hp, +33%) and torque from 175 to 250 Nm (+75 Nm). ECU — Bosch EDC17C10. Flashing method: OBD or Bench depending on the unit's protection. The 2008 generation — first-generation CDI/TDI/HDi diesels with relatively simple ECU protection; OBD reading works directly.
The Peugeot logo, a lion, has been the brand's traditional symbol since the 1850s. Peugeot Sport is the performance division that builds GTi models and track-focused variants. Within Stellantis, Peugeot shares platforms and engines with Citroen, Opel/Vauxhall and DS. Low-output Citroen diesels are city units, and Stage 1 is safe.
The Peugeot community in France offers a large pool of Stage files. Within Stellantis, ECUs are standardised, so Peugeot files often work on Citroen/Opel/DS. Low-output Citroen engines are city units, and Stage 1 is safe. On naturally aspirated Citroen engines, the main effect is on throttle response.
Frequently asked questions
What power gain do you get after chip tuning the Peugeot Partner 1.6 HDI (2008) 75 hp?
The Stage 1 gain for the Peugeot Partner 1.6 HDI (2008) 75 hp is 25 hp (+33%) over the stock 75 hp, for a total of 100 hp. Torque rises from 175 to 250 Nm (+75 Nm).
What is Stage 1 chip tuning for the Peugeot Partner?
Stage 1 on the Peugeot Partner 1.6 HDI (2008) 75 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +25 hp with no hardware changes.
Is Stage 1 safe for the low-output Peugeot Partner 1.6 HDI (2008) 75 hp?
Stage 1 on the base Peugeot Partner is safe — the factory calibration of low-output engines leaves headroom for software optimization. The gain is modest, but engine life is not affected.
How does Stage 2 differ from Stage 1 on the Peugeot Partner 1.6 HDI (2008) 75 hp?
Stage 2 on the Peugeot Partner 1.6 HDI (2008) 75 hp means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
What control unit does the Peugeot Partner 1.6 HDI (2008) 75 hp run?
The control unit of the Peugeot Partner 1.6 HDI (2008) 75 hp is the Bosch EDC17C10. Before flashing, the engineer identifies the exact revision and selects the write method.
Does Stage 1 void the warranty on the Peugeot Partner?
Stage 1 on the Peugeot Partner voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Peugeot Partner 1.6 HDI (2008) 75 hp done?
The full remap cycle for the Peugeot Partner — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Peugeot Partner?
The original Peugeot Partner ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Peugeot Partner 1.6 HDI (2008) 75 hp?
The cost of Stage 1 for the Peugeot Partner 1.6 HDI (2008) 75 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.