Peugeot Boxer 3.0 HDI 180 hp — Stage 1 file (+35 hp)
hp
Stage 1 file for Peugeot Boxer 3.0 HDI 180 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Peugeot Boxer 3.0 HDI 180 hp ECU
Peugeot Boxer (2014) 3.0 HDI 180 hp — mass-market diesel engine of the passenger segment of the Stellantis group (Франция, 1810). Stage 1 chip tuning raises power from 180 to 215 hp (+35 hp, +19%) and torque from 400 to 500 Nm (+100 Nm). ECU — Bosch EDC17CP52. Flashing method: OBD or Bench depending on the unit's protection. A diesel built in 2014 — the Tricore ECU era; OBD flash works on most production revisions.
Peugeot Sport is the performance division that builds GTi models and track-focused variants. Within Stellantis, Peugeot shares platforms and engines with Citroen, Opel/Vauxhall and DS. The Peugeot range covers compacts, saloons, SUVs, crossovers and commercial vehicles. HDi and BlueHDi are Citroen's badges for direct-injection turbo diesels.
On Peugeot diesels, Stage 1 delivers a noticeable torque gain. On older-generation Peugeot models, Stage 1 is done via OBD without bench. Within Stellantis, ECUs are standardised, so Peugeot files often work on Citroen/Opel/DS. The French Citroen community has a large pool of ready-made Stage files. Mid-range Citroen engines are a mainstream chip tuning subject in Europe.
Frequently asked questions
How many horsepower does the Peugeot Boxer 3.0 HDI 180 hp reach after a remap?
Stage 1 for the Peugeot Boxer 3.0 HDI 180 hp adds +35 hp — power increases from 180 to 215 hp (+19%). Torque rises from 400 to 500 Nm (+100 Nm).
What does a Stage 1 remap of the Peugeot Boxer 3.0 HDI 180 hp include?
Stage 1 is a software optimization of the factory ECU firmware of the Peugeot Boxer with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +35 hp with no hardware changes.
What is the risk of Stage 1 on the Peugeot Boxer 3.0 HDI 180 hp?
A remap of the Peugeot Boxer 3.0 HDI 180 hp is safe — the factory calibration in this mid-range class is conservative, leaving genuine headroom for Stage 1 with no hardware changes.
What is Stage 2 for the Peugeot Boxer 3.0 HDI 180 hp?
Stage 2 for the Peugeot Boxer 3.0 HDI 180 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What ECU platform does the Peugeot Boxer 3.0 HDI 180 hp use?
The Peugeot Boxer 3.0 HDI 180 hp is fitted with the Bosch EDC17CP52 ECU. The read method depends on the unit's protection: OBD, Bench via BDM, or Boot mode.
Does the factory warranty of the Peugeot Boxer remain valid after Stage 1?
After remapping the Peugeot Boxer, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Peugeot Boxer?
Reading and writing via OBD takes 25-30 minutes on the Peugeot Boxer. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Peugeot Boxer?
Before Stage 1 the original of the Peugeot Boxer 3.0 HDI 180 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Peugeot Boxer 3.0 HDI 180 hp cost?
The remap price for the Peugeot Boxer 3.0 HDI 180 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.