Peugeot 308 1.6 HDI 92 hp — Stage 1 file (+23 hp)
hp
Stage 1 file for Peugeot 308 1.6 HDI 92 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Peugeot 308 1.6 HDI 92 hp ECU
Peugeot 308 (2013) 1.6 HDI 92 hp — mass-market diesel engine of the passenger segment of the Stellantis group (Франция, 1810). Stage 1 chip tuning raises power from 92 to 115 hp (+23 hp, +25%) and torque from 230 to 270 Nm (+40 Nm). ECU — Bosch EDC17C10. Flashing method: OBD or Bench depending on the unit's protection. In the CHIPOK database: 2 configurations. The 2013 generation — mid-generation diesels on the EDC17 platform with OBD reading support and no need for Bench.
The Peugeot logo, a lion, has been the brand's traditional symbol since the 1850s. Peugeot Sport is the performance division that builds GTi models and track-focused variants. Within Stellantis, Peugeot shares platforms and engines with Citroen, Opel/Vauxhall and DS. The Citroen diesel range is fully shared with Peugeot, Opel and DS within Stellantis.
Within Stellantis, ECUs are standardised, so Peugeot files often work on Citroen/Opel/DS. On older-generation Peugeot models, Stage 1 is done via OBD without bench. The Peugeot community in France offers a large pool of Stage files. Low-output Citroen engines are city units, and Stage 1 is safe. On naturally aspirated Citroen engines, the main effect is on throttle response.
Frequently asked questions
How many horsepower does the Peugeot 308 1.6 HDI 92 hp reach after a remap?
After Stage 1 the power of the Peugeot 308 1.6 HDI 92 hp rises from 92 to 115 hp, a gain of 23 hp (+25%). Torque rises from 230 to 270 Nm (+40 Nm).
How does Stage 1 differ from stock on the Peugeot 308?
Stage 1 on the Peugeot 308 1.6 HDI 92 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +23 hp with no hardware changes.
Is Stage 1 safe for the low-output Peugeot 308 1.6 HDI 92 hp?
Stage 1 on the base Peugeot 308 is safe — the factory calibration of low-output engines leaves headroom for software optimization. The gain is modest, but engine life is not affected.
How does Stage 2 differ from Stage 1 on the Peugeot 308 1.6 HDI 92 hp?
Stage 2 on the Peugeot 308 1.6 HDI 92 hp means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
What control unit does the Peugeot 308 1.6 HDI 92 hp run?
The control unit of the Peugeot 308 1.6 HDI 92 hp is the Bosch EDC17C10. Before flashing, the engineer identifies the exact revision and selects the write method.
Does Stage 1 void the warranty on the Peugeot 308?
Stage 1 on the Peugeot 308 voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Peugeot 308 1.6 HDI 92 hp done?
The full remap cycle for the Peugeot 308 — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Peugeot 308?
The original Peugeot 308 ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Peugeot 308 1.6 HDI 92 hp?
The cost of Stage 1 for the Peugeot 308 1.6 HDI 92 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.