Opel Mokka 1.6 CDTI 136 hp — Stage 1 file (+19 hp)
hp
Stage 1 file for Opel Mokka 1.6 CDTI 136 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Opel Mokka 1.6 CDTI 136 hp ECU
Opel Mokka (2012) 1.6 CDTI 136 hp — mass-market diesel engine of the passenger segment of the Stellantis group (Германия, 1862). Stage 1 chip tuning raises power from 136 to 155 hp (+19 hp, +14%) and torque from 320 to 370 Nm (+50 Nm). ECU — Delco E98. Flashing method: OBD or Bench depending on the unit's protection. A diesel built in 2012 — the Tricore ECU era; OBD flash works on most production revisions.
Opel OPC is the performance division, producing high-output turbo versions. Opel shares platforms with Peugeot, Citroen and DS within Stellantis since 2017. Before 2017, Opel shared platforms with Chevrolet and Buick as part of GM. HDi and BlueHDi are Citroen's badges for direct-injection turbo diesels.
Older Opel models (pre-2017) share ECUs with Chevrolet, requiring a different toolset. On Opel diesels, Stage 1 delivers a noticeable torque gain. Within Stellantis, ECUs are standardised, so Opel files (from 2017 on) often work on Peugeot/Citroen. The French Citroen community has a large pool of ready-made Stage files. Mid-range Citroen engines are a mainstream chip tuning subject in Europe.
Frequently asked questions
How much does the power of the Opel Mokka 1.6 CDTI 136 hp increase after Stage 1?
Stage 1 chip tuning on the Opel Mokka 1.6 CDTI 136 hp boosts engine output by 19 hp: from 136 to 155 hp. Torque rises from 320 to 370 Nm (+50 Nm).
What changes in the Opel Mokka ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the Opel Mokka with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +19 hp with no hardware changes.
What is the risk of Stage 1 on the Opel Mokka 1.6 CDTI 136 hp?
A remap of the Opel Mokka 1.6 CDTI 136 hp is safe — the factory calibration in this mid-range class is conservative, leaving genuine headroom for Stage 1 with no hardware changes.
What is Stage 2 for the Opel Mokka 1.6 CDTI 136 hp?
Stage 2 for the Opel Mokka 1.6 CDTI 136 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What ECU platform does the Opel Mokka 1.6 CDTI 136 hp use?
The Opel Mokka 1.6 CDTI 136 hp is fitted with the Delco E98 ECU. The read method depends on the unit's protection: OBD, Bench via BDM, or Boot mode.
Does the factory warranty of the Opel Mokka remain valid after Stage 1?
After remapping the Opel Mokka, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Opel Mokka?
Reading and writing via OBD takes 25-30 minutes on the Opel Mokka. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Opel Mokka?
Before Stage 1 the original of the Opel Mokka 1.6 CDTI 136 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Opel Mokka 1.6 CDTI 136 hp cost?
The remap price for the Opel Mokka 1.6 CDTI 136 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.