Land-Rover Velar 3.0 P400 MHEV 400 hp — Stage 1 file (+40 hp)
hp
Stage 1 file for Land-Rover Velar 3.0 P400 MHEV 400 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Land-Rover Velar 3.0 P400 MHEV 400 hp ECU
Land-Rover Velar (2017) 3.0 P400 MHEV 400 hp — premium petrol engine of the passenger segment of the Tata Motors (Jaguar Land Rover) group (Великобритания, 1922). Stage 1 chip tuning raises power from 400 to 440 hp (+40 hp, +10%) and torque from 550 to 630 Nm (+80 Nm). ECU — Bosch MG1CS028. Flashing method: OBD or Bench depending on the unit's protection. The ZF 8HPxx TCU is calibrated with a separate file — torque limiter and shift maps for Stage 1. In the CHIPOK database: 2 configurations · 2 ECU variants. A petrol engine built in 2017 — a Tricore platform without strong protection; OBD access works.
Land Rover shares platforms and engines with Jaguar within JLR. Land Rover is a British manufacturer of premium off-roaders and SUVs, founded in 1948. Land Rover is part of Tata Motors via Jaguar Land Rover (JLR). The Jaguar V8 Supercharged is an iconic premium-segment engine. Jaguar's petrol range spans turbocharged Ingenium units and supercharged V6/V8 engines. The supercharged Jaguar V8 has significant potential with hardware upgrades.
The supercharged Jaguar V8 comfortably reaches Stage 2 with the right hardware. The Jaguar community is a premium chip tuning niche in the UK and Europe. The top Jaguar SVR engines (supercharged V8) mark the ceiling of British premium performance.
SVR models use a reinforced ZF 8HP. Jaguar uses the ZF 8HP, a premium 8-speed automatic.
Frequently asked questions
How much horsepower does Stage 1 add for the Land-Rover Velar 3.0 P400 MHEV 400 hp?
Stage 1 chip tuning on the Land-Rover Velar 3.0 P400 MHEV 400 hp boosts engine output by 40 hp: from 400 to 440 hp. Torque rises from 550 to 630 Nm (+80 Nm).
What changes in the Land-Rover Velar ECU after Stage 1?
Stage 1 on the Land-Rover Velar 3.0 P400 MHEV 400 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +40 hp with no hardware changes.
What does Stage 1 give on the top-spec Land-Rover Velar 3.0 P400 MHEV 400 hp?
On the top-spec Land-Rover Velar 3.0 P400 MHEV 400 hp engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
How does Stage 2 differ from Stage 1 on the Land-Rover Velar 3.0 P400 MHEV 400 hp?
Stage 2 for the Land-Rover Velar 3.0 P400 MHEV 400 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What control unit does the Land-Rover Velar 3.0 P400 MHEV 400 hp run?
The control unit of the Land-Rover Velar 3.0 P400 MHEV 400 hp is the Bosch MG1CS028. Before flashing, the engineer identifies the exact revision and selects the write method.
Does the ZF 8HPxx transmission need calibration after Stage 1 on the Land-Rover Velar?
Remapping the ZF 8HPxx gearbox is essential to fully unlock Stage 1 on the Land-Rover Velar 3.0 P400 MHEV 400 hp. Without a TCU update the factory torque cap will choke the torque gain and shifts will become noticeably softer.
Does Stage 1 void the warranty on the Land-Rover Velar?
Stage 1 on the Land-Rover Velar voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Land-Rover Velar 3.0 P400 MHEV 400 hp done?
The full remap cycle for the Land-Rover Velar — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Land-Rover Velar?
The original Land-Rover Velar ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Land-Rover Velar 3.0 P400 MHEV 400 hp?
The cost of Stage 1 for the Land-Rover Velar 3.0 P400 MHEV 400 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.