Iveco EuroTech E39 390hp (287kW) 1850Nm — Stage 1 file (+55 hp)
hp
Stage 1 file for Iveco EuroTech E39 390hp (287kW) 1850Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Iveco EuroTech E39 390hp (287kW) 1850Nm ECU
Iveco EuroTech (I) E39 390hp (287kW) 1850Nm — commercial diesel engine of the commercial segment of the Iveco Group / CNH Industrial group (Италия, 1975). Stage 1 chip tuning raises power from 390 to 445 hp (+55 hp, +14%) and torque from 1850 to 2120 Nm (+270 Nm).
Iveco shares some engines with Case and New Holland within CNH/FPT. Iveco is an Italian manufacturer of trucks and commercial vehicles, founded in 1975. Iveco is part of the Iveco Group (spun off from CNH Industrial in 2022). The factory calibration is conservative, leaving headroom for Stage 1 while preserving engine life. Truck chip tuning is a discipline of its own, focused on fuel consumption and pulling power rather than peak output. DPF/SCR with AdBlue is standard on modern Euro-6 truck engines.
The truck chip tuning community is an industry of its own, focused on long-haul routes. The professional logistics segment tunes for fuel consumption and pulling characteristics. Top MAN units sit at the power ceiling of the European truck segment.
Frequently asked questions
How much horsepower does Stage 1 add for the Iveco EuroTech E39 390hp (287kW) 1850Nm?
Stage 1 for the Iveco EuroTech E39 390hp (287kW) 1850Nm adds +55 hp — power increases from 390 to 445 hp (+14%). Torque rises from 1850 to 2120 Nm (+270 Nm).
What does a Stage 1 remap of the Iveco EuroTech E39 390hp (287kW) 1850Nm include?
Stage 1 on the Iveco EuroTech E39 390hp (287kW) 1850Nm is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +55 hp with no hardware changes.
What does Stage 1 give on the top-spec Iveco EuroTech E39 390hp (287kW) 1850Nm?
On the top-spec Iveco EuroTech E39 390hp (287kW) 1850Nm engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
How does Stage 2 differ from Stage 1 on the Iveco EuroTech E39 390hp (287kW) 1850Nm?
Stage 2 for the Iveco EuroTech E39 390hp (287kW) 1850Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does Stage 1 void the warranty on the Iveco EuroTech?
Stage 1 on the Iveco EuroTech voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Iveco EuroTech E39 390hp (287kW) 1850Nm done?
The full remap cycle for the Iveco EuroTech — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Iveco EuroTech?
The original Iveco EuroTech ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Iveco EuroTech E39 390hp (287kW) 1850Nm?
The cost of Stage 1 for the Iveco EuroTech E39 390hp (287kW) 1850Nm is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.