Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm — Stage 1 file (+53 hp)
hp
Stage 1 file for Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm ECU
Iveco Cursor (I) Cursor8 - 310 310hp (228kW) 1115Nm — commercial diesel engine of the commercial segment of the Iveco Group / CNH Industrial group (Италия, 1975). Stage 1 chip tuning raises power from 310 to 363 hp (+53 hp, +17%) and torque from 1115 to 1240 Nm (+125 Nm).
Iveco is an Italian manufacturer of trucks and commercial vehicles, founded in 1975. Iveco is part of the Iveco Group (spun off from CNH Industrial in 2022). The Iveco Daily is a high-volume commercial van in Europe. Truck chip tuning is a discipline of its own, focused on fuel consumption and pulling power rather than peak output. DPF/SCR with AdBlue is standard on modern Euro-6 truck engines. Truck diesels carry an extended set of maps for commercial load, with the focus on torque.
On high-output trucks, Stage 1 reduces fuel consumption under load. The professional logistics segment tunes for fuel consumption and pulling characteristics. The truck chip tuning community is an industry of its own, focused on long-haul routes. High-output MAN units are long-haul tractors with solid headroom for Stage 1.
Frequently asked questions
How much horsepower does Stage 1 add for the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm?
The Stage 1 gain for the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm is 53 hp (+17%) over the stock 310 hp, for a total of 363 hp. Torque rises from 1115 to 1240 Nm (+125 Nm).
What is Stage 1 chip tuning for the Iveco Cursor?
Stage 1 is a software optimization of the factory ECU firmware of the Iveco Cursor with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +53 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the Iveco Cursor?
The high-output Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm has a conservative factory calibration aimed at the mass market. Stage 1 unlocks the engine's real potential while turbo and injector life are preserved.
What is Stage 2 for the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm?
Stage 2 on the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Does the factory warranty of the Iveco Cursor remain valid after Stage 1?
After remapping the Iveco Cursor, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Iveco Cursor?
Reading and writing via OBD takes 25-30 minutes on the Iveco Cursor. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Iveco Cursor?
Before Stage 1 the original of the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm cost?
The remap price for the Iveco Cursor Cursor8 - 310 310hp (228kW) 1115Nm is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.