Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm — Stage 1 file (+53 hp)
hp
Stage 1 file for Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm
Target +0 hp. Custom development for your engine.
Chip tuning for Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm ECU
Iveco Cursor (I) Cursor8 - 300 296hp (218kW) 1110Nm — commercial diesel engine of the commercial segment of the Iveco Group / CNH Industrial group (Италия, 1975). Stage 1 chip tuning raises power from 296 to 349 hp (+53 hp, +18%) and torque from 1110 to 1230 Nm (+120 Nm).
The Iveco Stralis and S-Way are long-haul tractor units. Cursor is the range of Iveco/CNH commercial diesel engines. Iveco shares some engines with Case and New Holland within CNH/FPT. Mid-generation truck models use standard OBD read/write. High-output diesels head the truck segment, and Stage 1 is especially felt in Nm. The factory calibration is conservative, leaving headroom for Stage 1 while preserving engine life.
On high-output trucks, Stage 1 reduces fuel consumption under load. The professional logistics segment tunes for fuel consumption and pulling characteristics. The truck chip tuning community is an industry of its own, focused on long-haul routes. High-output MAN units are long-haul tractors with solid headroom for Stage 1.
Frequently asked questions
How much does the power of the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm increase after Stage 1?
Stage 1 chip tuning on the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm boosts engine output by 53 hp: from 296 to 349 hp. Torque rises from 1110 to 1230 Nm (+120 Nm).
What changes in the Iveco Cursor ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the Iveco Cursor with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +53 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the Iveco Cursor?
Stage 1 on the powerful Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
What is Stage 2 for the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm?
Stage 2 for the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Does the factory warranty of the Iveco Cursor remain valid after Stage 1?
After remapping the Iveco Cursor, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Iveco Cursor?
Reading and writing via OBD takes 25-30 minutes on the Iveco Cursor. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Iveco Cursor?
Before Stage 1 the original of the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm cost?
The remap price for the Iveco Cursor Cursor8 - 300 296hp (218kW) 1110Nm is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.