Hummer H3 3.5i 220 hp — Stage 1 file (+10 hp)
hp
Stage 1 file for Hummer H3 3.5i 220 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Hummer H3 3.5i 220 hp ECU
Hummer H3 (2005) 3.5i 220 hp — mass-market petrol engine of the passenger segment of the General Motors group (США, 1911). Stage 1 chip tuning raises power from 220 to 230 hp (+10 hp, +5%) and torque from 305 to 320 Nm (+15 Nm). ECU — Delphi 12597521. Flashing method: OBD or Bench depending on the unit's protection. A petrol engine built in 2005 — the era before widespread firmware encryption, OBD flash without complications.
The Hummer EV is GMC's flagship electric pickup. Hummer is an American off-road brand; legacy models ran until 2010, and the GMC Hummer EV revived it in 2021. Hummer was originally derived from the military HMMWV. GM ECUs (E78/E80/E92) are Bosch-based but use their own checksum. The LS-series V8 is Chevrolet's iconic engine range dating from 1997. Chevrolet 2.0 / 1.4 Turbo are mainstream turbo engines for saloons and compacts.
HP Tuners is the primary tool for Chevrolet/GM in the US. LS-swap is an industry of its own (Chevy LS engines into any car). The US Chevrolet community is the largest for Camaro, Corvette and LS-swaps. High-output Chevrolet Camaro / Silverado offer solid headroom for Stage 1.
Frequently asked questions
How many horsepower does the Hummer H3 3.5i 220 hp reach after a remap?
Stage 1 for the Hummer H3 3.5i 220 hp adds +10 hp — power increases from 220 to 230 hp (+5%). Torque rises from 305 to 320 Nm (+15 Nm).
What does a Stage 1 remap of the Hummer H3 3.5i 220 hp include?
Stage 1 on the Hummer H3 3.5i 220 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +10 hp with no hardware changes.
What does Stage 1 give on the powerful Hummer H3 3.5i 220 hp?
Stage 1 on the powerful Hummer H3 3.5i 220 hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
How does Stage 2 differ from Stage 1 on the Hummer H3 3.5i 220 hp?
Stage 2 for the Hummer H3 3.5i 220 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What control unit does the Hummer H3 3.5i 220 hp run?
The control unit of the Hummer H3 3.5i 220 hp is the Delphi 12597521. Before flashing, the engineer identifies the exact revision and selects the write method.
Does Stage 1 void the warranty on the Hummer H3?
Stage 1 on the Hummer H3 voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Hummer H3 3.5i 220 hp done?
The full remap cycle for the Hummer H3 — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Hummer H3?
The original Hummer H3 ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Hummer H3 3.5i 220 hp?
The cost of Stage 1 for the Hummer H3 3.5i 220 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.