Fiat Panda 1.3 Mjet 95 hp — Stage 1 file (+20 hp)
hp
Stage 1 file for Fiat Panda 1.3 Mjet 95 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Fiat Panda 1.3 Mjet 95 hp ECU
Fiat Panda (2017) 1.3 Mjet 95 hp — mass-market diesel engine of the passenger segment of the Stellantis (бывш. FCA — Fiat Chrysler Automobiles) group (Италия, 1899). Stage 1 chip tuning raises power from 95 to 115 hp (+20 hp, +21%) and torque from 200 to 250 Nm (+50 Nm). This engine ships with different ECU variants: Marelli MJD8, Marelli MJD8DMF, Marelli MJD8F2, Marelli MJD8F3. The flashing method is determined by the specific unit: OBD, Bench or Boot mode. In the CHIPOK database: 4 configurations · 4 ECU variants. The 2017 generation — mid-generation diesels on the EDC17 platform with OBD reading support and no need for Bench.
MultiAir is Fiat's own valve-control technology. Low-output Fiat diesels are city units, and Stage 1 is safe on them.
On pre-2017 Fiat models, Stage 1 is done via OBD without bench. The Fiat community in Italy offers a large pool of ready-made Stage files for compacts and the Ducato. Within Stellantis, ECUs are standardised across platforms, so some files work on Fiat/Citroen/Peugeot. Low-output Fiat engines are city units, and Stage 1 is safe on them. On naturally aspirated Fiat engines the main effect is sharper throttle response.
Frequently asked questions
What is the Stage 1 effect on the Fiat Panda 1.3 Mjet 95 hp?
After Stage 1 the power of the Fiat Panda 1.3 Mjet 95 hp rises from 95 to 115 hp, a gain of 20 hp (+21%). Torque rises from 200 to 250 Nm (+50 Nm).
How does Stage 1 differ from stock on the Fiat Panda?
Stage 1 is a software optimization of the factory ECU firmware of the Fiat Panda with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +20 hp with no hardware changes.
Is Stage 1 worth doing on the base Fiat Panda?
Stage 1 on the base Fiat Panda is safe — the factory calibration of low-output engines leaves headroom for software optimization. The gain is modest, but engine life is not affected.
What is Stage 2 for the Fiat Panda 1.3 Mjet 95 hp?
Stage 2 on the Fiat Panda 1.3 Mjet 95 hp means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Which control units is the Fiat Panda 1.3 Mjet 95 hp built with?
The Fiat Panda 1.3 Mjet 95 hp comes with 4 ECU variants: Marelli MJD8, Marelli MJD8DMF, Marelli MJD8F2, Marelli MJD8F3. Calibration is done for the specific unit after the revision is identified.
Does the factory warranty of the Fiat Panda remain valid after Stage 1?
After remapping the Fiat Panda, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Fiat Panda?
Reading and writing via OBD takes 25-30 minutes on the Fiat Panda. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Fiat Panda?
Before Stage 1 the original of the Fiat Panda 1.3 Mjet 95 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Fiat Panda 1.3 Mjet 95 hp cost?
The remap price for the Fiat Panda 1.3 Mjet 95 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.