Ferrari F8 3.9 T 720 hp — Stage 1 file (+50 hp)
hp
Stage 1 file for Ferrari F8 3.9 T 720 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Ferrari F8 3.9 T 720 hp ECU
Ferrari F8 (2020) 3.9 T 720 hp — luxury petrol engine of the passenger segment of the Ferrari N.V. (независимый, спин-офф из FCA в 2016) group (Италия, 1939). Stage 1 chip tuning raises power from 720 to 770 hp (+50 hp, +7%) and torque from 770 to 880 Nm (+110 Nm). ECU — Bosch MED17.3.5. Flashing method: OBD or Bench depending on the unit's protection. A 2020 petrol engine — the latest era of encrypted firmware; OBD access is available on production units, Bench on sport models.
Ferrari has its own F1 works and a Grand Prix heritage dating back to the 1950s. Ferrari is an Italian supercar manufacturer from Maranello, founded in 1939 by Enzo Ferrari. Ferrari has been independent from Stellantis since 2016 (Ferrari N.V.). Top-tier Ferrari engines have significant potential with a downpipe + intake. Ferrari's naturally aspirated V12s are a distinct calibration segment. Modern Ferrari models are heavily encrypted and usually require Bench.
Protection on modern Ferrari models is tight, so Bench is required. With the right hardware, Ferrari engines comfortably reach Stage 2. The Ferrari community is an ultra-premium chip tuning segment and a narrow niche. A Bench read is standard procedure on modern Ferraris. Top-tier Ferrari engines sit at the power ceiling of the supercar segment.
Frequently asked questions
How much horsepower does Stage 1 add for the Ferrari F8 3.9 T 720 hp?
Stage 1 for the Ferrari F8 3.9 T 720 hp adds +50 hp — power increases from 720 to 770 hp (+7%). Torque rises from 770 to 880 Nm (+110 Nm).
What does a Stage 1 remap of the Ferrari F8 3.9 T 720 hp include?
Stage 1 on the Ferrari F8 3.9 T 720 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +50 hp with no hardware changes.
What does Stage 1 give on the top-spec Ferrari F8 3.9 T 720 hp?
On the top-spec Ferrari F8 3.9 T 720 hp engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
How does Stage 2 differ from Stage 1 on the Ferrari F8 3.9 T 720 hp?
Stage 2 for the Ferrari F8 3.9 T 720 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What control unit does the Ferrari F8 3.9 T 720 hp run?
The control unit of the Ferrari F8 3.9 T 720 hp is the Bosch MED17.3.5. Before flashing, the engineer identifies the exact revision and selects the write method.
Does Stage 1 void the warranty on the Ferrari F8?
Stage 1 on the Ferrari F8 voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the Ferrari F8 3.9 T 720 hp done?
The full remap cycle for the Ferrari F8 — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the Ferrari F8?
The original Ferrari F8 ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the Ferrari F8 3.9 T 720 hp?
The cost of Stage 1 for the Ferrari F8 3.9 T 720 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.