DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm — Stage 1 file (+44 hp)
hp
Stage 1 file for DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm
Target +0 hp. Custom development for your engine.
Chip tuning for DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm ECU
DAF CF Euro6 (I) MX11 (EU6) 290hp (213kW) 1200Nm — commercial diesel engine of the commercial segment of the PACCAR (с 1996) group (Нидерланды, 1928). Stage 1 chip tuning raises power from 290 to 334 hp (+44 hp, +15%) and torque from 1200 to 1400 Nm (+200 Nm).
DAF specialises in long-haul tractor units and medium-duty trucks. DAF has been part of the American PACCAR group since 1996. DAF is a Dutch truck manufacturer, founded in 1928. Truck diesels carry an extended set of maps for commercial load, with the focus on torque. DPF/SCR with AdBlue is standard on modern Euro-6 truck engines. Truck chip tuning is a discipline of its own, focused on fuel consumption and pulling power rather than peak output.
The truck chip tuning community is an industry of its own, focused on long-haul routes. On high-output trucks, Stage 1 reduces fuel consumption under load. The professional logistics segment tunes for fuel consumption and pulling characteristics. High-output MAN units are long-haul tractors with solid headroom for Stage 1.
Frequently asked questions
What is the Stage 1 effect on the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm?
The Stage 1 gain for the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm is 44 hp (+15%) over the stock 290 hp, for a total of 334 hp. Torque rises from 1200 to 1400 Nm (+200 Nm).
What is Stage 1 chip tuning for the DAF CF Euro6?
Stage 1 on the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +44 hp with no hardware changes.
What does Stage 1 give on the powerful DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm?
The high-output DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm has a conservative factory calibration aimed at the mass market. Stage 1 unlocks the engine's real potential while turbo and injector life are preserved.
How does Stage 2 differ from Stage 1 on the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm?
Stage 2 on the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
Does Stage 1 void the warranty on the DAF CF Euro6?
Stage 1 on the DAF CF Euro6 voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm done?
The full remap cycle for the DAF CF Euro6 — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the DAF CF Euro6?
The original DAF CF Euro6 ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm?
The cost of Stage 1 for the DAF CF Euro6 MX11 (EU6) 290hp (213kW) 1200Nm is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.