Chevrolet Camaro 3.6 V6 (chevrole) 305 hp — Stage 1 file (+20 hp)
hp
Stage 1 file for Chevrolet Camaro 3.6 V6 (chevrole) 305 hp
Target +0 hp. Custom development for your engine.
Chip tuning for Chevrolet Camaro 3.6 V6 (chevrole) 305 hp ECU
Chevrolet Camaro (2011) 3.6 V6 (chevrole) 305 hp — mass-market petrol engine of the passenger segment of the General Motors group (США, 1911). Stage 1 chip tuning raises power from 305 to 325 hp (+20 hp, +7%) and torque from 375 to 390 Nm (+15 Nm). This engine ships with different ECU variants: Delco E39, Delco E82, Delco T87. The flashing method is determined by the specific unit: OBD, Bench or Boot mode. In the CHIPOK database: 3 configurations · 3 ECU variants. A petrol engine built in 2011 — a Tricore platform without strong protection; OBD access works.
The Camaro and Corvette are Chevrolet's iconic muscle and sports cars. The Silverado is Chevrolet's flagship pickup. Chevrolet shares platforms with GMC, Cadillac and Buick within GM. The LT-series V8 is the modern LS replacement, fitted to Camaro/Corvette/Silverado. GM ECUs (E78/E80/E92) are Bosch-based but use their own checksum. The LS-series V8 is Chevrolet's iconic engine range dating from 1997.
LS-swap is an industry of its own (Chevy LS engines into any car). The US Chevrolet community is the largest for Camaro, Corvette and LS-swaps. HP Tuners is the primary tool for Chevrolet/GM in the US. High-output Chevrolet Camaro / Silverado offer solid headroom for Stage 1.
Frequently asked questions
What power gain do you get after chip tuning the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp?
Stage 1 for the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp adds +20 hp — power increases from 305 to 325 hp (+7%). Torque rises from 375 to 390 Nm (+15 Nm).
What does a Stage 1 remap of the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp include?
Stage 1 is a software optimization of the factory ECU firmware of the Chevrolet Camaro with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +20 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the Chevrolet Camaro?
Stage 1 on the powerful Chevrolet Camaro 3.6 V6 (chevrole) 305 hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
What is Stage 2 for the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp?
Stage 2 for the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
Which control units is the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp built with?
The Chevrolet Camaro 3.6 V6 (chevrole) 305 hp comes with 3 ECU variants: Delco E39, Delco E82, Delco T87. Calibration is done for the specific unit after the revision is identified.
Does the factory warranty of the Chevrolet Camaro remain valid after Stage 1?
After remapping the Chevrolet Camaro, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the Chevrolet Camaro?
Reading and writing via OBD takes 25-30 minutes on the Chevrolet Camaro. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the Chevrolet Camaro?
Before Stage 1 the original of the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp cost?
The remap price for the Chevrolet Camaro 3.6 V6 (chevrole) 305 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.