BMW M2 3.0T (Comp.) 410 hp — Stage 1 file (+90 hp)
hp
Stage 1 file for BMW M2 3.0T (Comp.) 410 hp
Target +0 hp. Custom development for your engine.
Chip tuning for BMW M2 3.0T (Comp.) 410 hp ECU
BMW M2 (2015 - F87) 3.0T (Comp.) 410 hp — premium petrol engine of the passenger segment of the BMW Group (Mini, Rolls-Royce, BMW Motorrad) group (Германия, 1916). Stage 1 chip tuning raises power from 410 to 500 hp (+90 hp, +22%) and torque from 550 to 680 Nm (+130 Nm). ECU — Bosch MEVD17.2.G. Flashing method: OBD or Bench depending on the unit's protection. The Temic DKG436 gen2 TCU is calibrated with a separate file — torque limiter and shift maps for Stage 1. In the CHIPOK database: 2 configurations · 2 ECU variants. A petrol engine built in 2015 — a Tricore platform without strong protection; OBD access works.
M GmbH is BMW's performance division, building M engines since 1972. Third-party flash platforms are an industry of their own for the BMW community.
Stage 1 on BMW usually stays within the standard timeframe, with no particular difficulty on the standard models. The BMW community is renowned for active tuning and a large pool of available Stage files. Top BMW engines confidently reach Stage 2 with a downpipe + intake + intercooler. Top BMW engines sit at the power ceiling, and the gain is significant. A well-known base once hardware is added (downpipe + intake + intercooler). Bench reading is the standard procedure for top engines in modern models.
The gearbox comes in versions by torque class, so its tolerance depends on the engine. The TCU rarely needs recalibration up to Stage 1+, as the torque limiter usually copes with the Nm gain. Mini and FWD compacts use a different TCU platform with its own tooling base.
Frequently asked questions
How many horsepower does the BMW M2 3.0T (Comp.) 410 hp reach after a remap?
Stage 1 chip tuning on the BMW M2 3.0T (Comp.) 410 hp boosts engine output by 90 hp: from 410 to 500 hp. Torque rises from 550 to 680 Nm (+130 Nm).
What changes in the BMW M2 ECU after Stage 1?
Stage 1 is a software optimization of the factory ECU firmware of the BMW M2 with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +90 hp with no hardware changes.
Does Stage 1 make sense on the BMW M2 3.0T (Comp.) 410 hp with this much power?
On the top-spec BMW M2 3.0T (Comp.) 410 hp engine, Stage 1 is the starting point before Stage 2 with a downpipe, intake and a larger intercooler. The mass-market factory calibration leaves substantial headroom for an aggressive software tune.
What is Stage 2 for the BMW M2 3.0T (Comp.) 410 hp?
Stage 2 for the BMW M2 3.0T (Comp.) 410 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What ECU platform does the BMW M2 3.0T (Comp.) 410 hp use?
The BMW M2 3.0T (Comp.) 410 hp is fitted with the Bosch MEVD17.2.G ECU. The read method depends on the unit's protection: OBD, Bench via BDM, or Boot mode.
What does remapping the Temic DKG436 gen2 gearbox give on the BMW M2 3.0T (Comp.) 410 hp?
The Temic DKG436 gen2 TCU is calibrated separately: the torque limit is raised, the shift maps are optimized for the Stage 1 characteristics, and launch control is re-tuned. The TCU file is flashed separately from the ECU.
Does the factory warranty of the BMW M2 remain valid after Stage 1?
After remapping the BMW M2, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the BMW M2?
Reading and writing via OBD takes 25-30 minutes on the BMW M2. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the BMW M2?
Before Stage 1 the original of the BMW M2 3.0T (Comp.) 410 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the BMW M2 3.0T (Comp.) 410 hp cost?
The remap price for the BMW M2 3.0T (Comp.) 410 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.