BMW 3-serie 30i 272 hp — Stage 1 file (+13 hp)
hp
Stage 1 file for BMW 3-serie 30i 272 hp
Target +0 hp. Custom development for your engine.
Chip tuning for BMW 3-serie 30i 272 hp ECU
BMW 3-serie (2008 - E90-LCI) 30i 272 hp — premium petrol engine of the passenger segment of the BMW Group (Mini, Rolls-Royce, BMW Motorrad) group (Германия, 1916). Stage 1 chip tuning raises power from 272 to 285 hp (+13 hp, +5%) and torque from 320 to 340 Nm (+20 Nm). ECU — Siemens/Continental MSD80. Flashing method: OBD or Bench depending on the unit's protection. The ZF 6HP EGS TCU is calibrated with a separate file — torque limiter and shift maps for Stage 1. In the CHIPOK database: 4 configurations · 2 ECU variants. A petrol engine built in 2008 — the era before widespread firmware encryption, OBD flash without complications.
M GmbH is BMW's performance division, building M engines since 1972. High-output BMW turbo petrol engines deliver a solid gain with Stage 1 on stock hardware. The BMW petrol range spans the mainstream segment and the sporting M-series. The factory calibration on BMW petrol engines is conservative, leaving headroom for Stage 1 without hardware changes.
Stage 1 on BMW usually stays within the standard timeframe, with no particular difficulty on the standard models. The BMW community is renowned for active tuning and a large pool of available Stage files. The hardware headroom allows a confident move to Stage 1 without changing the turbo. High-output engines deliver a solid gain with Stage 1 on stock hardware. The BMW premium segment is a high-output platform with Stage 2 potential.
Mini and FWD compacts use a different TCU platform with its own tooling base. The TCU rarely needs recalibration up to Stage 1+, as the torque limiter usually copes with the Nm gain. The gearbox comes in versions by torque class, so its tolerance depends on the engine.
Frequently asked questions
How many horsepower does the BMW 3-serie 30i 272 hp reach after a remap?
Stage 1 for the BMW 3-serie 30i 272 hp adds +13 hp — power increases from 272 to 285 hp (+5%). Torque rises from 320 to 340 Nm (+20 Nm).
What does a Stage 1 remap of the BMW 3-serie 30i 272 hp include?
Stage 1 on the BMW 3-serie 30i 272 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +13 hp with no hardware changes.
What does Stage 1 give on the powerful BMW 3-serie 30i 272 hp?
Stage 1 on the powerful BMW 3-serie 30i 272 hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
How does Stage 2 differ from Stage 1 on the BMW 3-serie 30i 272 hp?
Stage 2 for the BMW 3-serie 30i 272 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What control unit does the BMW 3-serie 30i 272 hp run?
The control unit of the BMW 3-serie 30i 272 hp is the Siemens/Continental MSD80. Before flashing, the engineer identifies the exact revision and selects the write method.
Does the ZF 6HP EGS transmission need calibration after Stage 1 on the BMW 3-serie?
Remapping the ZF 6HP EGS gearbox is essential to fully unlock Stage 1 on the BMW 3-serie 30i 272 hp. Without a TCU update the factory torque cap will choke the torque gain and shifts will become noticeably softer.
Does Stage 1 void the warranty on the BMW 3-serie?
Stage 1 on the BMW 3-serie voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the BMW 3-serie 30i 272 hp done?
The full remap cycle for the BMW 3-serie — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the BMW 3-serie?
The original BMW 3-serie ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the BMW 3-serie 30i 272 hp?
The cost of Stage 1 for the BMW 3-serie 30i 272 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.