BMW 3-serie 28i 233 hp — Stage 1 file (+35 hp)
hp
Stage 1 file for BMW 3-serie 28i 233 hp
Target +0 hp. Custom development for your engine.
Chip tuning for BMW 3-serie 28i 233 hp ECU
BMW 3-serie (2005 - E90) 28i 233 hp — premium petrol engine of the passenger segment of the BMW Group (Mini, Rolls-Royce, BMW Motorrad) group (Германия, 1916). Stage 1 chip tuning raises power from 230 to 265 hp (+35 hp, +15%) and torque from 271 to 322 Nm (+51 Nm). ECU — Siemens/Continental MSV70. Flashing method: OBD or Bench depending on the unit's protection. The ZF 6HP EGS TCU is calibrated with a separate file — torque limiter and shift maps for Stage 1. In the CHIPOK database: 2 configurations · 2 ECU variants. A petrol engine built in 2005 — the era before widespread firmware encryption, OBD flash without complications.
The BMW community is one of the most active in Europe for chip tuning. High-output BMW turbo petrol engines deliver a solid gain with Stage 1 on stock hardware. The BMW petrol range spans the mainstream segment and the sporting M-series. The factory calibration on BMW petrol engines is conservative, leaving headroom for Stage 1 without hardware changes.
Stage 1 on BMW usually stays within the standard timeframe, with no particular difficulty on the standard models. The BMW community is renowned for active tuning and a large pool of available Stage files. High-output engines deliver a solid gain with Stage 1 on stock hardware. The BMW premium segment is a high-output platform with Stage 2 potential. The hardware headroom allows a confident move to Stage 1 without changing the turbo.
Mini and FWD compacts use a different TCU platform with its own tooling base. The TCU rarely needs recalibration up to Stage 1+, as the torque limiter usually copes with the Nm gain. The gearbox comes in versions by torque class, so its tolerance depends on the engine.
Frequently asked questions
How many horsepower does the BMW 3-serie 28i 233 hp reach after a remap?
Stage 1 for the BMW 3-serie 28i 233 hp adds +35 hp — power increases from 230 to 265 hp (+15%). Torque rises from 271 to 322 Nm (+51 Nm).
What does a Stage 1 remap of the BMW 3-serie 28i 233 hp include?
Stage 1 is a software optimization of the factory ECU firmware of the BMW 3-serie with no hardware changes. The injection, boost, ignition-timing and torque maps are reprogrammed. The gain is +35 hp with no hardware changes.
Do you need hardware changes for Stage 1 on the BMW 3-serie?
Stage 1 on the powerful BMW 3-serie 28i 233 hp “lifts” the factory limiters with no hardware changes. The gain is noticeable in the mid and upper range. There is headroom left for moving to Stage 2 (downpipe + intake + intercooler).
What is Stage 2 for the BMW 3-serie 28i 233 hp?
Stage 2 for the BMW 3-serie 28i 233 hp is Stage 1 plus hardware changes: a downpipe, a larger intake and a performance intercooler. The gain is considerably higher, but it requires professional component selection.
What ECU platform does the BMW 3-serie 28i 233 hp use?
The BMW 3-serie 28i 233 hp is fitted with the Siemens/Continental MSV70 ECU. The read method depends on the unit's protection: OBD, Bench via BDM, or Boot mode.
What does remapping the ZF 6HP EGS gearbox give on the BMW 3-serie 28i 233 hp?
The ZF 6HP EGS TCU is calibrated separately: the torque limit is raised, the shift maps are optimized for the Stage 1 characteristics, and launch control is re-tuned. The TCU file is flashed separately from the ECU.
Does the factory warranty of the BMW 3-serie remain valid after Stage 1?
After remapping the BMW 3-serie, the official factory warranty on the engine and gearbox is lost (this applies to any manufacturer when the ECU is modified). CHIPOK guarantees the quality of the calibration and free revisions.
How long is the wait for a Stage 1 remap for the BMW 3-serie?
Reading and writing via OBD takes 25-30 minutes on the BMW 3-serie. Bench reading (BDM/JTAG) takes about 60 minutes plus refitting. Remote file processing at CHIPOK takes 5-30 minutes.
How do you roll back to the factory firmware of the BMW 3-serie?
Before Stage 1 the original of the BMW 3-serie 28i 233 hp is read out and saved — returning to the factory state is possible at any time.
How much does chip tuning the BMW 3-serie 28i 233 hp cost?
The remap price for the BMW 3-serie 28i 233 hp is dynamic and is calculated in the CHIPOK calculator based on the selected options. A credit-based payment model, with no subscription fees.