BMW 3-serie 28i 193 hp — Stage 1 file (+10 hp)
hp
Stage 1 file for BMW 3-serie 28i 193 hp
Target +0 hp. Custom development for your engine.
Chip tuning for BMW 3-serie 28i 193 hp ECU
BMW 3-serie (1998 - E46) 28i 193 hp — premium petrol engine of the passenger segment of the BMW Group (Mini, Rolls-Royce, BMW Motorrad) group (Германия, 1916). Stage 1 chip tuning raises power from 193 to 203 hp (+10 hp, +5%) and torque from 280 to 295 Nm (+15 Nm). ECU — Siemens/Continental MS42. Flashing method: OBD or Bench depending on the unit's protection. The 1998 generation — old-era petrol ECUs (ME7/ME9/MED9/Simos) with easily readable memory.
xDrive all-wheel drive is BMW's signature system. The BMW petrol range spans the mainstream segment and the sporting M-series. The factory calibration on BMW petrol engines is conservative, leaving headroom for Stage 1 without hardware changes. On older-generation BMW petrol engines, Stage 1 goes in over OBD without Bench.
Stage 1 on BMW usually stays within the standard timeframe, with no particular difficulty on the standard models. Stage 1 on standard mid-range BMW petrol engines delivers a noticeable gain with no hardware changes. The BMW community is renowned for active tuning and a large pool of available Stage files. The factory calibration is conservative, with headroom for Stage 1 and no hardware changes. Mid-range engines form the backbone of the range, and Stage 1 preserves engine life. The mainstream base is the most refined chip tuning segment in Europe.
Frequently asked questions
How much horsepower does Stage 1 add for the BMW 3-serie 28i 193 hp?
The Stage 1 gain for the BMW 3-serie 28i 193 hp is 10 hp (+5%) over the stock 193 hp, for a total of 203 hp. Torque rises from 280 to 295 Nm (+15 Nm).
What is Stage 1 chip tuning for the BMW 3-serie?
Stage 1 on the BMW 3-serie 28i 193 hp is a software ECU calibration with no hardware changes. The key maps (boost/ignition/lambda/torque) are adjusted while factory tolerances are preserved. The gain is +10 hp with no hardware changes.
Is a Stage 1 remap safe for the 28i 193 hp?
Stage 1 on the BMW 3-serie 28i 193 hp is developed while keeping the factory AFR, knock control and temperature limits. Engine life is preserved provided regular maintenance is carried out.
How does Stage 2 differ from Stage 1 on the BMW 3-serie 28i 193 hp?
Stage 2 on the BMW 3-serie 28i 193 hp means software + hardware (exhaust, intake, intercooler). The gain depends on the specific hardware combination.
What control unit does the BMW 3-serie 28i 193 hp run?
The control unit of the BMW 3-serie 28i 193 hp is the Siemens/Continental MS42. Before flashing, the engineer identifies the exact revision and selects the write method.
Does Stage 1 void the warranty on the BMW 3-serie?
Stage 1 on the BMW 3-serie voids the factory warranty on the engine and transmission — this is standard for all manufacturers. CHIPOK provides its own warranty on the quality of the remap.
How quickly is chip tuning of the BMW 3-serie 28i 193 hp done?
The full remap cycle for the BMW 3-serie — from reading to writing the final file — takes 30-90 minutes depending on the ECU access method. The file is prepared at CHIPOK in 5-30 minutes.
Can you return to stock after Stage 1 on the BMW 3-serie?
The original BMW 3-serie ECU is always saved before flashing. Rolling back to the factory firmware is done with the same programmer in 25-30 minutes.
How much does Stage 1 cost for the BMW 3-serie 28i 193 hp?
The cost of Stage 1 for the BMW 3-serie 28i 193 hp is calculated in the calculator on this page — you select the options (DPF off, EGR off, AdBlue off, DTC off, etc.) and the price is capped by the package Max Price. Payment is by credits (1 cr = 1 €), with no subscriptions.